Thermocouple & Thermometer & Temperature controller & 50-segment PID programmable controller

50-segment PID programmable controller


SP-P908	SP-P909	SP-P916

With functions of AI controller, 50-segment PID programmable controllers are applicable where the given value needs to be controlled automatically following certain rules of time. The given increase/decrease slope can be set at will, so as to get the capacity of slope heating/cooling or curve heating. With PID control arithmetic and without excessive and insufficient adjustment, the reading in and out of all instrument parameters and function of heating power segment limit can be realized on upper computers, together with functions including step control, manual/auto switch of no disturb as well as self-tuning. With 4-digit LED digital display, the measurement value and setting value as well as operation time can be displayed at the same time. The control object can be controlled by programming in up to 50 segments of curve, each of which adopts PID parameter setting control, making control more precise and reliable.
1.   The setting scope for each segment of time is from 1 to 1999 minutes or from 1 to 19999 seconds.
2.   With the jumping functions of the 1st to 30th segment of program, the memory and run of several different curves can be realized.
3.   With RUN/HOLD function, the time counting starts and the given value changes following the pre-scheduled program when the program runs and time counting stops and the given value is unchanged when the program holds.
4.   The running program segment and remaining time to run this segment can be surveyed during running.
5.   With 2-channel event output function, the event output generates under programming. The 2-channel alarm ON/OFF action can be controlled during program running, so that various external equipments are easy to work in phase or in chain.
6.   With RDY and measurement activation functions, it can automatically resolve the uncertainty to the program caused by inconsistency between measurement value and setting value when starting running.

Technical parameters of SP-P900 series 50-segment PID programmable control instruments

Overall indexes	Voltage of power supply	85-265VAC/50-60HZ or 24VCD/AC+10％,-15％
	Environment temperature	0-55℃
	Environment humidity	＜90％RH
	Measurement precision	0.2degree(±0.2％FS±1 number or 0.1℃)
Measurement PV	Input signal	Thermocouple: B、S、K、E、T、J
		Thermal resistor:pt100 、Cu50
		Current :0~10 mA 0~20mA 4~20mA
		Voltage；；0~60mV 0~100 mV 0~1V 0~5 V?? 1~5 V
		Resistance :0~80Ω 0~400Ω
	Input resistance	Input resistance>500kΩ when o to 5v or 1to 5v and >10mΩ for signals including thermocouple
	Resolution	1℃ for thermocouple and thermal resistor input ,the range is 1/20000 for 0.1℃ linear voltage input
	Digital filter	0 to 40 times can be set (0 to 20s)
Setting segment SV	Setting mode	On-site operation by buttons2.upper computer through communication interface (lifespan of 1 million red-in)
	Setting scope	-200to+3000℃for thermocouple and thermal resistor inputs and -1999to +9999 for other inputs
	Data storage	EEPROM being adopted, no data loss when deactivating,10 years of reliable storage
Automatic adjustment and calculation segment	Step adjustment	2-phase style,3-phase style and non-sensitive alarm section are supported:0 to 200℃ or 0 to 2000 defined units (linear measurement)
	AI adjustment	Retention parameter:0 to 9999×0.1℃ or 1 defined unit (for linear measurement)
		Speed parameter:1 to 9999×0.01s℃ or 1 defined unit (for linear measurement)
		Delay :0.5 to 3600s
		Self-tuning:(AT) time is at (2 to 3 cycles) after ON/OFF action of a position of given value
Adjustment output segment	AI adjustment time proportion output	Solid state relay trigger output:12v/30mA
		Zero passage silicon-control output :bidirectional or double single-directional SCR anti-correlation below 500A can be directly triggered
		Non-contact normally open ON/OFF output :100v to 240VAC/0.2A,instant maximum:2A
		Relay ON/OFF output :250VAC/2A,normally open + normally close 6.control cycle: settable between 0.5 and 120s
	Continuous current output	Loaded resistance≥1kΩ when 0 to 10mA and ≥500Ωwhen 4 to20 mA
	Continuous voltage output	Loaded resistance≦250Ωwhen 0 to 5V and≦250Ω when 1 to 5v
Alarm output segment	Alarm mode	Maximum alarm, minimum alarm, plus deviation alarm, minus deviation alarm
	Non-sensitive alarm section	0.0 to 200.0℃or 0 to 2000 defined units(for linear measurement)
	Baud rate	1200~19200bps
	Data format	1 start bit, 8-digit data, 1 to 2 end bit
Transmission output	Check mode	16-digit summing check
	Output type	Randomly specified within the scope from 0 to 22mA when o to 10mA or 4 to 20mA
	Maximum output voltage	≥10.5v
	Transmission precision	0.3％FS
Feedback out put	Output specification	5V,10V,12V,or 24V is optional
Feedback out put	Maximum current	50mA

Model selection sheet for SP-P900 series 50-segment PID programmable control instruments

SP								Specification
	P9							Function of 50-segment program control added based on SP-900
Dimension		08						Panel dimension:80×160mm(W×H),insert depth:140mm
		09						Panel dimension: 96×96mm,insert depth:100mm
		16						Panel dimension:160×80mm(W×H),insert depth:140mm
Main output(OUT)			x					Photo-isolated linear current output module (programmable for 0 to 10mA, 0 to 20mA and 4 to 20mA )
			L2					Relay contact ON/OFF(voltage-dependent resistance absorption) output module(capacity:250VAC/1A)
			L4					Large-capacity long-lifespan relay normally-open contact ON/OFF output module(capacity:250VAC/2A)
			G					Solid state relay-driven voltage output module(capacity:DC12V/30mA )
			W1					SCR non-contact normally-open ON/OFF output module (capacity:100 to 240VAC/0.2A)
			W2					SCR non-contact normally-close ON/OFF output module(capacity:100 to 240VAC/0.2A)
			K1					Single channel SCR zero passage trigger output module(various SCR from 5 to 500A can be triggered)
			K5					Single-channel SCR phase-shifting trigger output module(various silicon-control from 5 to 500A can be triggered)
Alarm1(AL1)				L2				Relay contract ON/OFF (voltage dependent resistance absorption) output module (capacity:250VAC/1A)
				L4				Large-capacity long-lifespan relay normally-open contact ON/OFF output module
				W1				SCR non-contact normally-open ON/OFF output module
				W2				SCR non-contact normally-close ON/OFF output module
				G				Solid state relay-driven voltage output module
				K1				Single channel SCR zero passage trigger output module(with main output to realize three-phase three-channel zero passage trigger)
Alarm2(AL2)					L2			Relay contract ON/OFF(voltage dependent resistance absorption) output module
					W1			SCR non-contact normally-close ON/OFF output module
					W2			SCR non-contact normally-open ON/OFF output module
Communication(COMM)						S		Photo-isolated RS-485 communication interface module
Communication(COMM)						V24		Isolated 24V DV output ,can be used for transmitter
Auxiliary interfaces(AUX)							L2	Relay contract ON/OFF(voltage dependent absorption) output module
							L4	Resistance-capacity absorption relay contact ON/OFF normally-open output module(large capacity and long lifespan)
							X	Photo-isolated linear current output module
							V24	Isolated 24V DV output ,can be used for transmitter
							U5	Non-isolated 5V DV output, can be used for value-position feedback potentiometer
							G	Solid state relay-driven voltage output module